Sipariş No
101170100
Sertifikalar
cULus TÜV CCC TÜV, cULus,
Schmersal
Emniyetli Anahtarlama ve Denetleme
Emniyet Konum Şalterleri (PS Serisi)
SRB301SQ 230V Emniyet Konum Şalterleri (PS Serisi)
SRB301SQ 230V — Schmersal Emniyet Konum Şalterleri (PS Serisi). Başlıca özellikler: Gövde Malzemesi: Glass-fibre reinforced thermoplastic, ventilated; Ortam Sıcaklığı: -25 ... +45 °C; Terminal Bağlantısı: Screw terminals; Depth: 121 mm; EPLAN: Yes. Ürün numarası: 101170100. Fiyat ve teslim süresi için teklif isteyebilirsiniz; teknik veriler ve belgeler aşağıdadır.
Ürün Açıklaması
- • Ağırlık: 250 g
- • Sertifika: cULus TÜV CCC TÜV, cULus,
Standartlar
- • EN IEC 60947-5-3
- • EN IEC 61508
- • EN IEC 62061
- • EN ISO 13849-1
- • EN IEC 60947-5-1
- • EN IEC 60947-5-5
- • EN IEC 60204-1
- • EN IEC 60947-1
Ürün Özellikleri
- • 3 safety contacts, STOP 0
- • 1 Signalling output
- • Kontak sensörlü çıkışların sinyal işlemesine uygun
Teknik Özellikler
Depth
121 mm
EPLAN
Yes
Montaj
Snaps onto standard DIN rail to EN 60715
Kategori
4
Genel Not
Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.
Genişlik
22.5 mm
PFH value
2.00 x 10⁻⁸ /h
EMC rating
EMC-Directive
Yükseklik
100 mm
Start input
Yes
Kablo Kesiti
0.25 mm² ... 2.5 mm²
Darbe Dayanımı
30 g / 11 ms
Stop-Category
0
Görev Süresi
20 Year(s)
Net Ağırlık
250 g
Number of LEDs
3
Climatic stress
EN 60068-2-78
Electronic Fuse
Yes
Frequency range
50 Hz | 60 Hz
Brüt Ağırlık
250 g
Feedback circuit
Yes
Gövde Malzemesi
Glass-fibre reinforced thermoplastic, ventilated
Kontak Malzemesi
AgSn0. kendi kendini temizleyen, pozitif tahrikli
Kirlenme Derecesi
2
Min. Kablo Kesiti
0.25 mm²
Operating voltage
48 ... 240 VAC
Titreşim Dayanımı
10 ... 55 Hz, Genlik 0.35 mm
Maks. Kablo Kesiti
2.5 mm²
Ortam Sıcaklığı
-25 ... +45 °C
Performans Seviyesi
e
Removable Terminals
Yes
Mekanik Ömür (min.)
10 000 000
Reset edge detection
Yes
Utilisation category
AC-15 | DC-13
Allowed type of cable
solid single-wire | flexible
Note (Wiring diagram)
Automatic start: The automatic start is programmed by connecting the feedback circuit to the terminals S12/X3. If the feedback circuit is not required, establish a bridge. | The control recognises cross-short, cable break and earth leakages in the monitoring circuit. | Relay outputs: Suitable for 2 channel control, for increase in capacity or number of contacts by means of contactors or relays with positive-guided contacts. | Input level: The example shows a 2-channel control of a guard door monitoring with two position switches, whereof one with positive break, external reset button (R); cross-wire monitoring and feedback circuit (H2) | The wiring diagram is shown with guard doors closed and in de-energised condition.
Terminal designations
IEC/EN 60947-1
Type of voltage range
AC
Terminal Bağlantısı
Screw terminals
Cross-circuit detection
Yes
Wire breakage detection
Yes
Automatic reset function
Yes
Min. Ortam Sıcaklığı
-25 °C
Note (Delivery capacity)
Not available!
Güvenlik Kontak Sayısı
3
Maks. Ortam Sıcaklığı
+45 °C
Note (Contact resistance)
in new state
Earth connection detection
Yes
Indicated operating states
Position relay K1 | Position relay K2
Kullanım Kategorisi AC-15
6 A | 230 VAC
Kullanım Kategorisi DC-13
6 A | 24 VDC | 24 VDC / 6 A
Tightening torque of Clips
0.6 Nm
Yardımcı Kontak Sayısı
1
Aşırı Gerilim Kategorisi
II | 2
Contact resistance, maximum
0.1 Ω
Nominal Çalışma Voltajı
48 ... 240 VAC
Electrical power consumption
2.8 VA
Switching frequency, maximum
5 Hz
Note (application conditions)
Pull-wire emergency stop switches | Emergency-Stop button | Guard system
Conduction resistance, maximum
40 Ω
Darbe Dayanım Gerilimi (Uimp)
4 kV
Diagnostic Coverage (DC) Level
> 99 %
Depolama / Taşıma Sıcaklığı
-40 ... +85 °C
Pull-in delay at RESET, typically
15 ms
Common Cause Failure (CCF), minimum
65
Integral system diagnostics, status
Yes
NK (Normalde Kapalı) Kontak Sayısı
2
IP Degree of protection of the enclosure
IP40
Pull-in delay at automatic start, maximum
35 ms
Rated control voltage at AC 50 Hz, maximum
240 VAC
Rated control voltage at AC 60 Hz, maximum
240 VAC
Storage and transport temperature, maximum
+85 °C
Storage and transport temperature, minimum
-40 °C
IP Degree of protection of clips or terminals
IP20
Rated AC voltage for controls, 50 Hz, minimum
48 VAC
Rated AC voltage for controls, 60 Hz, minimum
48 VAC
Drop-out delay in case of emergency, typically
20 ms
IP Degree of protection of the installation space
IP54
Drop-out delay in case of "emergency stop", maximum
25 ms
Pull-in delay at automatic start, maximum, typically
30 ms
Safety Integrity Level (SIL), suitable for applications in
3